Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Ellicott City: What to Know First
An Olympia Chimney liner replacement or rebuild in Ellicott City typically runs $1,200 to $4,600 depending on flue height, liner material, and whether the masonry crown or smoke chamber needs work at the same time. Most liner installs take one day; a full rebuild usually runs two to three. We’re an independent Olympia Chimney service provider, not a manufacturer rep, so we quote the repair honestly whether the fix is a $300 patch or a full replacement. If you own a home in Ellicott City with an Olympia Chimney product and you’re seeing rust flakes, draft problems, or water in the firebox, call (443) 363-5262 for a written estimate. Every quote includes a camera scan of the flue before we quote a single number.
How Olympia Chimney Products Fail - and How We Fix Them
- Stainless steel liner corrosion on Olympia rigid single-wall liners. We see this repeatedly in Ellicott City homes built before 2010. The liner walls develop pinhole rust where appliance exhaust condenses against cold masonry overnight. The fix is usually a full liner replacement with a 316L alloy, which resists the acidic condensate that eats 430-grade steel. We do not patch rusted liners. The camera footage shows why: once pinholes start, the wall behind them is thin enough to flex under hand pressure.
- Mortar joint failure at the liner-to-flue transition. Olympia Chimney components mate with a poured or refractory joint that shrinks over time. When it cracks, exhaust leaks into the chase or the gap between liner and masonry. We remove the old joint, repack with refractory cement, and re-secure the liner with a locking top plate. On older Olympia installations, we also check for missing or rusted locking rings, a common source of differential movement.
- Flex liner kinking in Olympia Chimney flex kits. The corrugated stainless flex sections Olympia sells for offsets can kink during installation if the angle exceeds 30 degrees. A kinked flex liner does not draft correctly and traps creosote at the bend. We either re-pull the liner with a smoother offset or switch to rigid sections for that run. The price difference is modest; the draft improvement is measurable with a manometer.
- Crown wash cracking over Olympia stainless caps. The crown holds the cap and liner terminator, and in Ellicott City’s freeze-thaw cycle, hairline crown cracks widen season after season. Rain follows the crack, rusts the liner top, and the rust streaks down the flue. We rebuild the crown with a proper overhang and drip edge, then reset the Olympia cap with a weather-sealed storm collar.
- Clay tile liner deterioration behind Olympia Chimney liners. In older Ellicott City chimneys with original clay tiles, the tiles spall and drop fragments into the annular space between tile and liner. Those fragments compress the liner from the outside. We remove the debris, verify the liner diameter is still round with the camera, and insulate the annular space where code allows. Without insulation, the liner runs cooler and condenses more.
Our Olympia Chimney Chimney Liner & Rebuild Process
Here’s how a typical Olympia Chimney liner or rebuild job runs with us in Ellicott City, from the first call to the final photo report.
- 1
Call and schedule. A live person answers at (443) 363-5262. We book a two-hour window and text when the tech is on the way, per the H.A.V.E.N. standard on verified crews and arrival windows.
- 2
Full camera scan. The tech runs a Level 2 camera down the flue. We look for the specific failure mode: liner corrosion, joint separation, kinked flex, crown wash damage, or hidden tile spalling. “The camera doesn’t soften what it finds - and neither do I,” Corrine Halstead will tell you, and she means it. You watch the footage in real time.
- 3
Written scope and price. Before any work starts, we put the exact scope on paper: which liner material, what gets replaced, what gets rebuilt, what we leave alone. The price is fixed. No add-ons, no “while we’re in there” surprises. This is Haven Standard Clause 1, Have it in writing.
- 4
Parts decision. Where an Olympia OEM part is the right call and available, we use it. Where a quality aftermarket liner or connector from DuraFlex, HeatShield, or Gelco performs better and costs less, we tell you why and give you the choice in writing. On Olympia flex kits with chronic kinking, we often recommend a rigid 316L replacement from our stock.
- 5
The repair or rebuild. We work in a contained zone, remove only what’s failed, and protect the hearth and home with floor runners and dust barriers. A liner replacement usually takes one day. A full rebuild with crown, flue, and smoke chamber work takes two to three.
- 6
Test, document, and guarantee. We re-run the camera after the job to prove the liner is seated, the joints are sealed, and the draft reads within spec. You get the photo record, the written warranty, and a copy of the written scope with the final price. Then it’s covered by our 365-Day Done Right Promise: if it’s not done right, we make it right.
BeforeAfterWhat Olympia Chimney Chimney Liner & Rebuild Costs in Ellicott City
| Job Type | Typical Range in Ellicott City | What Moves the Price |
|---|---|---|
| Flex liner replacement, single story | $1,200 - $2,200 | Flue height, roof pitch, existing cap condition |
| Rigid 316L liner replacement | $1,800 - $3,200 | Number of offsets, whether insulation is added |
| Liner repair (joint, locking ring, minor section) | $300 - $800 | Accessibility from roof vs. firebox |
| Crown and liner terminator rebuild | $900 - $1,800 | Masonry condition, scaffold vs. ladder access |
| Full chimney rebuild from roofline up | $3,500 - $6,500+ | Flue height, brick matching, structural reinforcement |
These are Ellicott City market numbers, not national averages. Older stone-foundation homes near Historic Ellicott City on Main Street tend to run higher because clearance tolerances are tighter and aged mortar requires more prep. The fastest way to get your exact number is a camera scan and a written quote. Call (443) 363-5262 for a free estimate. We also offer a Free Second Opinion on any written estimate you bring us from another contractor.
Why Ellicott City Homeowners Call Level Two Chimney Ellicott City for Olympia Chimney Work
We’ve inspected and cleaned more than 38,000 chimneys since 2009, and every single one had a written price before work started and a documented photo record when it was done. That’s not marketing language; it’s Clause 4 of the Haven Standard, the inspection standard we built the company around. When we work on an Olympia Chimney liner in Ellicott City, our techs know the brand’s failure patterns because they’ve pulled failed liner sections out of flues all over Howard County. We stock Olympia-compatible components, and when a different brand serves you better, we carry DuraFlex, HeatShield, and Gelco and we tell you in plain terms why we’d switch. Every tech is background-checked and uniformed. License information is on every page. And our calls are answered by a live person 24/7, not a voicemail and not a web form.
FAQs
We’re an independent Olympia Chimney service provider, so we do not administer Olympia’s manufacturer warranty. What we do is give you a written warranty on our workmanship and materials for every liner and rebuild job, backed by the 365-Day Done Right Promise. If a defect is traced to Olympia’s manufacturing, we document it with camera footage and help you file the claim. Call (443) 363-5262 and we’ll walk you through what your warranty actually covers.
It depends on what the camera shows. A failed locking ring, a leaking joint, or a partially detached top plate can usually be repaired for $300 to $800. Pinhole corrosion, a kinked flex section, or liner walls that flex under hand pressure mean replacement. We do not patch rusted liners; the wall behind the rust is already compromised. The estimate includes the footage so you see exactly why we recommend what we recommend.
Most liner replacements are scheduled within one to two weeks, and the job itself takes one day for a single-story flue. Full rebuilds take two to three days on site. We text you when the tech is en route and you get a written schedule before we start. Call (443) 363-5262 to get on the calendar.
We use OEM Olympia parts when they’re the best available and in stock. When an aftermarket 316L liner from DuraFlex, HeatShield, or Gelco outlasts the original Olympia component and costs less, we recommend it and put the reasoning in writing before any work starts. You make the final call. Our goal is a liner that drafts properly for 20 years, not brand loyalty for its own sake.
You get the complete camera footage from before and after, a written scope of work, the final paid invoice showing the fixed price, and a written warranty on materials and workmanship. Every visit includes a documented photo record under Haven Standard Clause 4. If you ever sell the home, this is the file the next owner and their inspector will want.
Ready to see what’s actually inside your Olympia Chimney flue? Call (443) 363-5262 and we’ll get a live person on the line, a tech on the schedule, and a written price in your hand before any work begins.
Written by Corrine Halstead, Owner, Level Two Chimney Ellicott City at Level Two Chimney Ellicott City, serving Ellicott City and nearby areas.